2007, 12-17 Permit App: 07003408 Remodel BasementProject Number: 07003408 Inv: 1
Application
THIS IS NOT A PERMIT
Penalties will be assessed for commencing work without a permit
Date: 12/17/2007 Page 1 of 2
Project Information:
Permit Use: FINISH REMODEL OF BASEMENT -DRYWALL
Setbacks: Front
Site Information:
Plat Key:
Left: Right: Rear:
Contact: PETERSON, MELISSA M/GAGE, JAME
Address: 24 S EDEN LN
C - S - Z: SPOKANE VALLEY, WA 99016
Phone: (509) 869-2305
Group Name:
Project Name:
Name: Corbin Estates Long Plat
District: East
Parcel Number: 55191.2726
SiteAddress: 24 S EDEN LN
Block:
Lot:
Owner: Name: PETERSON, MELISSA M/GAGE, J
Address: 24 S EDEN LN
Location:: CSV . SPOKANE VALLEY, WA 99016
Zoning: UR -7* Urban Residential -7*
Water District: 134 CONSOLIDATED ID #19
Area:
6,647 Sq Ft Width: 0
Nbr of Bldgs: 0 Nbr of Dwellings: 0
Review Information: +
Hold: ❑
0 Right Of Way (ft): 0
Review
Building Plan Review
4-sQ
Permits:
Released By: -
Origiily leased: 8/31/2007 By: tmelbourn
Contractor: OWNER
Building Permit
Firm: OWNER
Phone: (000) 000-0000
This Application: Total Project:
Description Grp Type Notes Sq Ft Valuation Sq Ft Valuation
BASEMENTU R-3 VB BASEMENT 0 $1,000.00 0 $1,000.00
FINISH
Item Description
RESIDENTIAL PERMIT FEE
WSBC SURCHARGE
SF PLNS RVW < 7999 SQ FT
Totals: 0 $1,000.00 0 $1,000.00
Units Unit Desc Fee Amount
1 SELECT $69.25
I SELECT $4.50
I SELECT $27.70
Operator: jmm Printed By: jmm
Permit Total Fees: $101.45
Print Date: 12/17/2007
Project Number: 07003408 Inv: 1
Notes:
Application
THIS IS NOT A PERMIT
Penalties will be assessed for commencing work without a permit
Date: 12/17/2007 Page 2 of 2
See plat file for TURTLE CREEK SOUTH 2ND for special drainage requirements
Payment Summary:
Permit Type
Building Permit
Fee Amount Invoice Amount
$101.45 $101.45
$101.45 $101.45
Amount Paid
$0.00
Amount Owing
$101.45
$0.00 $101.45
Disclaimer:
Submittal of this application certifies the owner (or person(s) authorized by the owner) has both examined and finds the information
contained within to be true and correct, and agrees that all provisions of laws and/or regulations governing this type of work will be
complied with. Subsequent issuance of a permit shall not be construed to be a permit for, or an approval of, any violation of any of
the provisions of the code or of any other state or local laws or ordinances.
Signature:
Operator: jmm Printed By: jmm Print Date: 12/17/2007
Permit Center
cruor •
11703 E Sprague Ave, Suite B-3
Spokane Spokane Valley, WA 9.9�20.6=1�
41,00
Valley (509)688-0036 FAX: (' ��.O�
aOF SP
Community Development
Residential Construction
Permit Application
DBALmt
9 Nal
PERMIT NUMBER:3 t!Q g
•
PERMIT FEE:
EConstruction
Other:
emodel
Accessory Bldg
Deck
SITE ADDRESS: oty S • EDCAA
SC:i L , WA- 9a 01,L0
ASSESSORS PARCEL NO: LEGAL DESCRIPTION:
Buildin` Owner: s" M "^ Y '^_
' ' ." to
..�g re •5a.. ,:.,_-2 :.•' .. s_
-..,... , r _�
'Coni'rictorr:. +:
.^rT?-r-rc::: A,a. s: .. ._�_. =s. _c'4---_�.
- - - .. _ ... ..
Name:
Name: "atm �d7cC.
Address: "4-i s --,0a
Address:
V, \ _.lJ4E State:um\ ZiPVPJ IL
City: scbtLis.Ae
City: State: Zip:
Phone: crack t�SFax:
2 2
u�
Phone: Fax:
DECK/COV. PATIO SQ. FTG:
Contractor Lic No: Exp Date:
;COntaht Person_ .; •: `, ;:; >t '` ; }'., _^� „. �`. ;`
CONSTRUCTION TYPE:
City Business Lic. No:
SEWER OR SEPTIC?
Name: J U-1/4 G 4_
Phone: eio`;1 2.3ccS
Describe the scope of work in detail:
Cost of Project: $ 1000 .
2e1/4Mi c %1.. o•C" SP.Seafhr1 i �t'yw cu,
Proposed Use: P:eo•omcara. 9M -+.1W teo1Jt
**************The following MUST be complete: (write N/A if not applicable)****************
*
HEIGHT TO PEAK:
DIMENSIONS:
# OF STORIES:
TOTAL HABITABLE SPACE:
MAIN FLOOR TO SQ.
FTG:
2Nu FLOOR SQ. FTG:
UNFIN BASEMENT SQ. FTG:
IMPERVIOUS SURFACE
AREA:
FINISHED B EMENT
SQ. FTG: 13 (,p C
GARAGE SQ. FTG:
DECK/COV. PATIO SQ. FTG:
30% SLOPES ON
PROPERTY:
# OF BEDR OMS:
CONSTRUCTION TYPE:
HEAT SOURCE:
SEWER OR SEPTIC?
The permitee verifies, acknowledges and agrees by their signature that: 1) If this permit is for construction of or on a dwelling, the
dwelling is/will be served by potable water. 2) Ownership of this City of Spokane Valley Permit inure to the property owner. 3) The
signatory is the property owner or has permission to represent the property owner in this transaction. 4) All construction is to be done
in full compliance with the City of Spokane Valley Development Code. Referenced codes are available for review at the City of
Spokane Valley Permit Center. 5) This City of Spokane Valley Permit is not a permit or approval for any violation of federal, state or
local laws, codes or ordinances. 6) Plans or additional information may be required to be submitted, and subsequently approved before
this application can be processed.
SIGNATUR
Method of Payment:
0 Cash 0 Check
Bankcard #:
Authorized Signature:
REVISED 2/1S/07
DATE: S. • 7_01 _ c7�
❑ Mastercard 0 VISA
Expires: VIN#:
Sp"„okane
Site Address: 24 S EDEN LN
Parcel Number: 55191.2726
Zoning: UR -7`
Fire District: FD 01
Project
Transmittal
City of Spokane Valley
Community Development
Department
11703 E. Sprague Ave, Suite B3
Spokane Valley, WA 99206
Phone: 509.688.0036
New projecr�
Previous pre -app .meeting
Plan revisions
Transmittal Dare:
Wednesday, August 29, 2007
Project Number: 07003408
Water District: CONSOLIDATED ID #19
Applicant: PETERSON, MELISSA M/GAGE, JA
24 S EDEN LN
SPOKANE VALLEY, WA 99016
(509) 869-2305
e-mail:
Contact: PETERSON, MELISSA M/GAGE, JA
24 S EDEN LN
SPOKANE VALLEY, WA 99016
(509) 869-2305
e-mail:
Contractor: OWNER
( ) - 0
Owner: PETERSON, MELISSA M/GAGE, JA
24 S EDEN LN
SPOKANE VALLEY, WA 99016
e-mail:
Occupant:
e-mail:
Arch / Engineer:
e-mail:
D
Eco "\\11E
AUG 2 2007
il EMHAF.j
Project FINISH REMODEL OF BASEMENT -DRYWALL
Description:
Building
Landuse
Engineer
Utilities
Health
Fire Dist
Assessor
APPLICATIO
t\
CONSTRUCTION PLAN
S
Please send all plan review and project comments via e-mail to the
highlighted individuals.
*""*" THIS CARD. PERMIT AND APPROVED PLANS SHALL BE ON JOB SITE AT ALL TIMES'******
*lane
jUalley' FOR INSPECTIONS CALL
509-688-0054
YOUR BUILDING INSPECTOR IS:
EAST AREA PRESS I
SOUTH AREA PRESS 2
NORTH AREA PRESS 3
THIS CARD MUST BE POSTED ON JOB SITE
COMMUNITY DEVELOPMENT DEPARTMENT BUILDING DIVISION
INSPECTION RECD
11703 E. Srague Ave, B-3 Job Address y S Ede".
Spokane Valley, WA 99216
Inspection request line (509)688-0054
PERMIT NO: % 3 y0
DATE
INSPECTOR
DATE
INSPECTOR
SETBACKS
WATER PIPING
FOOTINGS
DRAIN / WASTE / VENT
REINFORCEMENT
INSULATION
UNDERGROUND
FIREWALL/GWB
RADON
FIRE PROTECTION SYSTEM
FRAMING
HVAC SYSTEM
GAS PIPING
FINAL BUILDING
DUCT WORK
FIRE
*lane
jUalley' FOR INSPECTIONS CALL
509-688-0054
YOUR BUILDING INSPECTOR IS:
EAST AREA PRESS I
SOUTH AREA PRESS 2
NORTH AREA PRESS 3
THIS CARD MUST BE POSTED ON JOB SITE
COMMUNITY DEVELOPMENT DEPARTMENT BUILDING DIVISION
INSPECTION RECD
11703 E. Srague Ave, B-3 Job Address y S Ede".
Spokane Valley, WA 99216
Inspection request line (509)688-0054
PERMIT NO: % 3 y0
)
WHEN INTERIOR ALTERATIONS. REPAIRS OR ADDITIONS
REQUIRING A PERMIT OCCUR. OR WHEN ONE OR MORE
SLEEPING ROOMS ARE ADDED OR CREATED IN EXISTING
`DWELLINGS. THE DWEWNG UNIT SHALL BE PROVIDED
WITH SMOKE ALARMS LOCATED AS REQUIRED FOR NEW
DWELLINGS.
SMOKE ALARMS SHALL OE INTERCON-
NECTED AND HARD WIRED IN SUCH A
MANNER THAT THE ACTIVATION OF ONE
ALARM WILL ACTIVATE ALL ALARMS.
(BEDROOMS, AREAS ,APPROACHING,
BEDROOMS, VAULTED CEILING
WITH RISE OF 24- & ON EACH FLOOR)
4r
50`'ba#h
D 1a V'e;NT o
EXT OQ
i
•
aclo hoot joisis lre.c.
•
•
y
•
1/I' ■ 1'
T
J
5 rF4 CSE -c 131of 3,-3
GARAGE
?1' z ivy
l ,r LMNG AREA
19e4•
44,44.1%
KN.0146 iTcL/� iZ f� j
STAIRWAYS: Minimum width 36 in. with min. tread
run of 10 in., max. rise of 7 3/4 in. & nosing of 3/4-1 '/4 in.
Min. headroom 6 ft. 8 in. Enclosed usable space under
stairways requires 1 hour fire protection of 'Ain. GWB
a
EMERGENCY EGRESS REQUIREMENTS
FROM SLEEPING ROOMS
1) NET CLEAR OPENING 5.7 SQUARE FEET
GRADE FLOOR OPENING (MAX 44•) 5.0 SQUARE FEET
2) NET CLEAR OPENING HEIGHT 24 INCHES
3) NET CLEAR OPENING WIDTH 20 INCHES
4) MAX FINISHED SILL HEIGHT 44• ABOVE FLOOR
5) EMERGENCY ESCAPE 8 RESCUE OPENING SHALL BE
OPERATIONAL FROM THE INSIDE OF THE ROOM WITHOUT
THF USE OF KEYS OR TOOLS
•
GENERAL REGULATIONS
301.15 Prohibited location. The appliances, equipment and
systems regulated by this code shall not be located in an eleva-
tor shaft.
SECTION 302 (IFGC)
STRUCTURAL SAFETY
[B] 302.1 Structural safety. The building shall not be weak-
ened by the installation of any gas piping. In the process of in-
stalling or repairing any gas piping, the finished floors, walls,
ceilings, tile work or any other part of the building or premises
which is required to be changed or replaced shall be left in a
safe structural condition in accordance with the requirements
of the International Building Code.
[B] 302.2 Penetrations of floor/ceiling assemblies and
fire -resistance -rated assemblies. Penetrations of floor/ceil-
ing assemblies and assemblies required to have a fire -resis-
tance rating shall be protected in accordance with the
International Building Code.
[B] 302.3 Cutting, notching and boring in wood members.
The cutting, notching and boring of wood members shall com-
ply with Sections 302.3.1 through 302.3.4.
[B] 302.3.1 Engineered wood products. Cuts, notches and
holes bored in trusses, laminated veneer lumber, glued -lam-
inated members and I -joists are prohibited except where the
effects of such alterations are specifically considered in the
design of the member.
[B] 302.3.2 Joist notching. Notching at the ends of joists
shall not exceed one-fourth the joist depth. Holes bored in
joists shall not be within 2 inches (51 mm) of the top and
bottom of the joist and their diameter shall not exceed
one-third the depth of the member. Notches in the top or bot-
tom of the joist shall not exceed one-sixth the depth and
shall not be located in the middle one-third of the span.
[B] 302.3.3 Stud cutting and notching. In exterior walls
and bearing partitions, any wood stud is permitted to be cut
or notched to a depth not exceeding 25 percent of its width.
Cutting or notching of studs to a depth not greater than 40
percent of the width of the stud is permitted in
nonload-bearing partitions supporting no loads other than
the weight of the partition.
[B] 302.3.4 Bored holes. A hole not greater in diameter than
40 percent of the stud depth is permitted to be bored in any
wood stud. Bored holes not greater than 60 percent of the
depth of the stud are permitted in nonload-bearing partitions
or in any wall where each bored stud is doubled, provided
not more than two such successive doubled studs are so
bored. In no case shall the edge of the bored hole be nearer
than 5/6 inch (15.9 mm) to the edge of the stud. Bored holes
shall not be located at the same section of stud as a cut or
notch.
[B] 302.4 Alterations to trusses. Truss members and compo-
nents shall not be cut, drilled, notched, spliced or otherwise al-
tered in any way without the written concurrence and approval
of a registered design professional. Alterations resulting in the
addition of loads to any member (e.g., HVAC equipment, water
heaters) shall not be permitted without verification that the
truss is capable of supporting such additional loading.
[B] 302.5 Cutting, notching and boring holes in structural
steel framing. The cutting, notching and boring of holes in
structural steel framing members shall be as prescribed by the
registered design professional.
[B] 302.6 Cutting, notching and boring holes in
cold -formed steel framing. Flanges and lips of load-bearing,
cold -formed steel framing members shall not be cut or notched.
Holes in webs of load-bearing, cold -formed steel framing
members shall be permitted along the centerline of the web of
the framing member and shall not exceed the dimensional limi-
tations, penetration spacing or minimum hole edge distance as
prescribed by the registered design professional. Cutting,
notching and boring holes of steel floor/roof decking shall be as
prescribed by the registered design professional.
[B] 302.7 Cutting, notching and boring holes in
nonstructural cold -formed steel wall framing. Flanges and
lips of nonstructural cold -formed steel wall studs shall be per-
mitted along the centerline of the web of the framing member,
shall not exceed 1112 inches (38 mm) in width or 4 inches (102
mm) in length, and the holes shall not be spaced less than 24
inches (610 mm) center to center from another hole or less than
10 inches (254 mm) from the bearing end.
SECTION 303 (IFGC)
APPLIANCE LOCATION
303.1 General. Appliances shall be located as required by this
section, specific requirements elsewhere in this code and the
conditions of the equipment and appliance listing.
303.2 Hazardous locations. Appliances shall not be located in
a hazardous location unless listed and approved for the specific
installation.
303.3 Prohibited locations. Appliances shall not be located in,
or obtain combustion air from, any of the following rooms or
spaces:
1. Sleeping rooms.
2. Bathrooms.
3. Toilet rooms.
4. Storage closets.
5. Surgical rooms.
Exceptions:
1. Direct -vent appliances that obtain all combustion air
directly from the outdoors.
2. Vented room heaters, wall furnaces, vented decorative
appliances and decorative appliances for installation
in vented solid fuel -burning fireplaces, provided that
the room meets the required volume criteria of Sec-
tion 304.5.
3. A single wall -mounted unvented room heater
equipped with an oxygen depletion safety shutoff sys-
tem and installed in a bathroom, provided that the in-
put rating does not exceed 6,000 Btu/h (1.76kW) and
the bathroom meets the required volume criteria of
Section 304.5.
4. A single wall -mounted unvented room heater
equipped with an oxygen depletion safety shutoff sys-
20 2003 INTERNATIONAL FUEL GAS CODE®
i
i
I
tem and installed in a bedroom, provided that the in-
put rating does not exceed 10,000 Btu/h (2.93 kW)
and the bedroom meets the required volume criteria of
Section 304.5.
5. Appliances installed in an enclosure in which all com-
bustion air is taken from the outdoors, in accordance
with Section 304.6. Access to such enclosure shall be
through a solid weather-stripped door, equipped with
an approved self-closing device.
303.4 Protection from physical damage. Appliances shall not
be installed in a location where subject to physical damage un-
less protected by approved barriers meeting the requirements
of the International Fire Code.
303.5 Indoor locations. Furnaces and boilers installed in clos-
ets and alcoves shall be listed for such installation.
303.6 Outdoor locations. Equipment installed in outdoor lo-
cations shall be either listed for outdoor installation or provided
with protection from outdoor environmental factors that influ-
ence the operability, durability and safety of the equipment.
303.7 Pit locations. Appliances installed in pits or excavations
shall not come in direct contact with the surrounding soil. The
sides of the pit or excavation shall be held back a minimum of
12 inches (305 mm) from the appliance. Where the depth ex-
ceeds 12 inches (305 mm) below adjoining grade, the walls of
the pit or excavation shall be lined with concrete or masonry,
such concrete or masonry shall extend a minimum of 4 inches
(102 mm) above adjoining grade and shall have sufficient lat-
eral load-bearing capacity to resist collapse. The appliance
shall be protected from flooding in an approved manner.
SECTION 304 (IFGS)
COMBUSTION, VENTILATION AND DILUTION AIR
304.1 General. Air for combustion, ventilation and dilution of
flue gases for gas utilization equipment installed in buildings
shall be provided by application of one of the methods pre-
scribed in Sections 304.5 through 304.9. Where the require-
ments of Section 304.5 are not met, outdoor air shall be
introduced in accordance with one of the methods prescribed in
Sections 304.6 through 304.9. Direct -vent appliances, gas ap-
pliances of other than natural draft design and vented gas appli-
ances other than Category I shall be provided with combustion,
ventilation and dilution air in accordance with the equipment
manufacturer's instructions.
Exception: Type 1 clothes dryers that are provided with
makeup air in accordance with Section 614.5.
304.2 Appliance/equipment location. Equipment shall be lo-
cated so as not to interfere with proper circulation of combus-
tion, ventilation and dilution air.
304.3 Draft hood/regulator location. Where used, a draft
hood or a barometric draft regulator shall be installed in the
same room or enclosure as the equipment served so as to pre-
vent any difference in pressure between the hood or regulator
and the combustion air supply.
I 304.4 Makeup air provisions. Makeup air requirements for
the operation of exhaust fans, kitchen ventilation systems,
GENERAL REGULATIONS
clothes dryers and fireplaces shall be considered in determining
the adequacy of a space to provide combustion air requirements.
304.5 Indoor combustion air. The required volume of indoor
air shall be determined in accordance with Section 304.5.1 or
304.5.2, except that where the air infiltration rate is known to be
less than 0.40 air changes per hour (ACH), Section 304.5.2
shall be used. The total required volume shall be the sum of the
required volume calculated for all appliances located within
the space. Rooms communicating directly with the space in
which the appliances are installed through openings not fur-
nished with doors, and through combustion air openings sized
and located in accordance with Section 304.5.3, are considered
to be part of the required volume.
304.5.1 Standard method. The minimum required volume
shall be 50 cubic feet per 1,000 Btu/h (4.8 m3/kW) of the ap-
pliance input rating.
304.5.2 Known air -infiltration -rate method. Where the
air infiltration rate of a structure is known, the minimum re-
quired volume shall be determined as follows:
For appliances other than fan -assisted, calculate volume
using Equation 3-1.
Required Volumes„ � n,. >_
21Jt 3 1 other
ACH (1,000 Btu I hr
(Equation 3-1)
For fan -assisted appliances, calculate volume using
Equation 3-2.
Required Volumern„ > 15 ft I fan
3
ACH 1,000 Btu / hr
(Equation 3-2)
where:
Toter = All appliances other than fan assisted (input in
Btu/h).
/fan = Fan -assisted appliance (input in Btu/h).
ACH = Air change per hour (percent of volume of space
exchanged per hour, expressed as a decimal).
For purposes of this calculation, an infiltration rate
greater than 0.60 ACH shall not be used in Equations 3-1
and 3-2.
304.5.3 Indoor opening size and location. Openings used
to connect indoor spaces shall be sized and located in accor-
dance with Sections 304.5.3.1 and 304.5.3.2 (see Figure
304.5.3).
304.5.3.1 Combining spaces on the same story. Each
opening shall have a minimum free area of 1 square inch
per 1,000 Btu/h (2,200 mm2/kW) of the total input rating
of all gas utilization equipment in the space, but not less
than 100 square inches (0.06 m2). One opening shall
commence within 12 inches (305 mm) of the top and one
opening shall commence within 12 inches (305 mm) of
the bottom of the enclosure. The minimum dimension of
air openings shall be not less than 3 inches (76 mm).
304.5.3.2 Combining spaces in different stories. The
volumes of spaces in different stories shall be considered
as communicating spaces where such spaces are con -
2003 INTERNATIONAL FUEL GAS CODE® 21
WINDOW WELL:
Min. 9 sq. ft. horizontal area.
Min. 3 ft. horizontal projection and width.
Max. 44 in. vertical depth without a ladder
47*
-- in—
rip es
I
404081. I I I
I
I
I
I 1 ..0
hi.
Lwow
i1.0 I 1
160
14 Fliers 7 6/1.•
J
4040111,
WHO
I 1
I
r
,-7 - -,-------- - . . k . 4
: I ...,,..__.. i )
ON Wilk WH......)
l•---,' --,..... 1/0% On Fun=
er.
WO floor pleb Ira&
DO 0 pax joists 1ro.c.
TUM
aC:1, 3! ,
a HT
• . C..1-3!1
1ff s I'
C3ARAGE
21 x 1179
1
r
I.
LIVING AR EA
21
THESE PLANS MUST BE KEPT
ON THE JOB SITE
THIS BUILDING SUBJECT
TO FIELD INSPECTION CORRECTIONS
REVIEWED FOR COMPLIANCE
SPOKANE VALLE\ SUiL IN G DIVISION
O