1997, 03-03 Permit App: 97001110 RemodelPROJECT NUMBER= 97001110 'APPLICATION
PROJECT NUMBER= 97001110 APPLICATION
DATE= 03/03/97
DATE= 03/03/97
PAGE= 01
PAGE= 01
****** THIS IS NOT A PERMIT ******
PENALTIES WILL BE ASSESSED FOR COMMENCING WORK WITHOUT A PERMIT
SITE STREET=
ADDRESS=
PERMIT USE=
7208 E UTAH AVE PARCEL#= 35121.9005
SPOKANE WA 99212
INTERIOR/EXTERIOR REM -INSULATION, PLUMBING, ROOFING,SIDING,WINDOW
PLAT#= 999999
BLOCK=
AREA= 00000000
# OF BLDGS= 1 #
OWNER=
STREET=
ADDRESS=
PLAT NAME= RANGE
LOT=
F/A= F
DWELLINGS=
LEGGETT, EDNA
7208 E UTAH AVE
SPOKANE WA 99212
ZONE= AGSUB
WIDTH=
1 WATER DIST
DIST#=
DEPTH=
H
R/W=
PHONE= 509 928 6646
CONTACT NAME= THOMAS TOLAR - TNT CONSTRUCTIO PHONE NUMBER= 208 773 1565
BUILDING SETBACKS: FRONT= NA LEFT= NA RIGHT= NA REAR= NA
****************************** REVIEW INFORMATION *****************************
DEPARTMENT REVIEW REQUIREMENT
BUILDING
PLAN REVIEW REQUIRED
APPROVAL: J SHATTO
DATE: 03/03/97
******************************* BUILDING PERMIT ****************************
CONTRACTOR= T N T CONSTRUCTION
STREET= 2700 E SELTICE WAY 2-266
ADDRESS= POST FALLS ID 83854
NEW=
DWELL UNITS=
BLDG W X D =
REQ PARKING=
REMODEL= X
1 OCCUP. LD=
X SQ FT=
#HANDICAP=
DESCRIPTION GROUP TYPE SQ FT
REMODEL R-3 VN
PHONE= 208 773 1565
ADDITION= CHANGE OF USE=
BLDG HGT= STORIES=
SPRINKLER= N
CRITICAL MAT= N
ITEM DESCRIPTION QUANTITY
RESIDENTIAL VALUATION
RESIDENTIAL SURCHARGE
STATE SURCHARGE
Y
Y
Y
VALUATION
7000.00
FEE AMOUNT
125.50
27.61
4.50
PROJECT NUMBER= 97001110 APPLICATION DATE= 03/03/97 PAGE= 02
******************************* MECHANICAL PERMIT **************************
CONTRACTOR= T N T CONSTRUCTION
STREET= 2700 E SELTICE WAY 2-266
ADDRESS= POST FALLS ID 83854
ITEM DESCRIPTION
VENTILATING FANS
PHONE= 208 773 1565
QUANTITY FEE AMOUNT
1 10.00
***************************** PLUMBING PERMIT ******************************
CONTRACTOR= THOMAS CLEMENS PLBG & HTG
STREET= 5718 N WALNUT ST
ADDRESS= SPOKANE WA 99205
ITEM DESCRIPTION
TUBS
SINKS
WATER PIPING - DWV
PERMIT TYPE
BUILDING PERMIT
MECHANICAL PRMT
PLUMBING PERMIT
PHONE= 509 328 3760
QUANTITY FEE AMOUNT
1
2
1
6.00
12.00
6.00
FEE AMOUNT AMOUNT PAID AMOUNT OWING
157.61
10.00
24.00
191.61
PROCESSED BY: JULIE SHATTO
PRINTED BY: JULIE SHATTO
.00
.00
.00
157.61
10.00
24.00
.00 191.61
******************************** THANK YOU ************************************
SNAP
SPOKANE NEIGHBORHOOD ACTION PROGRAMS
Administrative Offices
2116 East First Avenue
Spokane, WA 99202-3147
(509) 456-7111 or FAX: 534-5874
PROJECT NUMBER: 8029
PROPERTY OWNER NAME: EDNA LEGGETT
PROPERTY ADDRESS: E. 7208 UTAH, SPOKANE 99212
Dear Contractor:
This cover sheet is to assist you in participating in the SNAP Housing Rehabilitation
bidding process. Please review this cover page for the general bid categories contained on
the BID SPECIFICATIONS LIST (BSL). In depth information on the project is outlined
on the BSL. If you are interested in bidding after reviewing this project, sign in at the bid
desk and pick up an "Invitation to Bid" packet. Please submit your bids within 10
working days - only the first five will be accepted.
The following housing rehabilitation will be completed for this project:
• CARPENTRY
• THERMAL & MOISTURE PROTECTION
• DOORS AND WINDOWS
• FINISHES
• PLUMBING
• ELECTRICAL
• PAINTING
• MASONRY
• VENTILATION
Thank you for your interest in the Spokane Neighborhood Action Programs.
A Community Action Agency
SNAPGJ
INVITATION TO BID
SPOKANE NEIGHBORHOOD ACTION PROGRAMS (SNAP)
SINGLE FAMILY HOUSING REHABILITATION PROGRAM
Date: DECEMBER 30, 1996 Invitation No: 8029
We invite you to submit your bid on work as listed below:
Owner:
Address:
Phone:
EDNA LEGGETT
E. 7208 Utah
Spokane, WA 99212
(509) 928-7858
Contractor Instructions:
Site visits by appointment only. Call
Homeowner to schedule.
If you have any questions regarding this Bid,
please contact MARK HUGHES, 456-7111,Ext.258
Sealed bids for the work herein will be received until: JANUARY 13 , 19 97 at 3:00 p.m. ,
and at that time will be publicly opened at Spokane Neighborhood Action Programs, 2116 East First
Avenue, Spokane, Washington 99202.
The Rehabilitation work on this home may be inclusive of several improvement projects which may or may
not be interrelated. YOU MUST BID ON THE ENTIRE PROJECT unless special individual project
bidding instructions are provided herein.
Special Instructions:
NOTE: Please submit your bid on the original Program Competitive Bid and Acceptance Form. No other form
will be accepted. The Competitive Bid section of the Program Competitive Bid and Acceptance Form must be
executed by the Contractor. Work specified is to be performed in accordance with all the contract documents, local
building codes, the attached specification list, the Program Contractor's Manual, DCTED Weatherization
Specifications, and any amendments officially issued.
NOTE: All bidders are required to visit the building site prior to submitting bids. All measurements are
approximate. Verify all measurements and conditions at the work site. No extra compensation will be allowed
because of differences between work shown and the actual measurements and conditions at the construction site.
El
LJ
SNAP
PROPERTY OWNER: Edna Leggett
PROPERTY ADDRESS: E. 7208 Utah Spokane, WA 99212
PROJECT NUMBER: 8029
SECTION
NUMBER
DESCRIPTION
NORTHWEST BEDROOM REPAIRS:
AREA # 1
0800
DOORS AND WINDOWS:
0801
Remove the two existing bedroom windows.
0802
North window - Install a vinyl framed "low E" picture window by adding stops and trim.
0803
Northwest window - Install a single hung; vinyl wrapped; "low E" no fm window with
stops and trim.
0804
Re -install the entry door handle and install set screws to hold the handle Tighten the
closet door handle Adjust and tighten both doors for proper operation.
1600
ELECTRICAL:
1601
Remove the existing ceiling fan/light and save for installation in the dining room.
1602
Install a single -gang cut -in box and a single pole switch. Install a fixture with a globe.
1603
Remove the existing light in the closet and install a porcelain pull chain fixture.
Install two duplex receptacles in cut -in boxes. The walls are marked for location.
1604
1800
PAINTING:
1801
Patch the holes and dings on the walls and ceilings. Skim coat with drywall compound
1802
Prime, texture and paint the bedroom side of both doors.
AREA #2
SECOND BEDROOM:
0800
DOORS AND WINDOWS:
0801
Remove the existing window and install a single -hung vinyl wrapped "low E" no fm . .
window to include stops and trim.
0802
Install set screws to both doors to hold the handles, tighten and adjust both doors.
1600
ELECTRICAL:
1601
Remove the existing light and install a fixture with a globe.
1602
Install a single gang cut -in box and a single pole switch for the light.
1603
Install two duplex receptacles in cut -in boxes. The walls are marked for location.
1604
Install a pull chain porcelain fixture in the closet.
1800
PAINTING:
1801
Patch the holes and dings in the walls. Skim coat with drywall compound, prime, texture
and paint.
1802
Square off the hole in the ceiling and install /" drywall, tape, skim coat, texture and paint
SECTION
NUMBER .
AREA #3
0800
0801
LAUNDRY ROOM:
0802
Page 2 of 6
DESCRIPTION
DOORS AND WNDOWS:
Remove the existing double hung window and install a single -hung, vinyl wrapped,
"low E" no fin window. Install stops and trim.
Adjust and repair the door between the laundry and the storage area. Install weatherstrip
around the door, install'a sweep at the bottom and install a security lock.
0900
0901
FINISHES:
Install approved underlayment, vinyl and cove base.
1500
1501
PLUMBING:
Remove the existing plumbing supplies and drain and install to current plumbing codes.
"T" off this plumbing and run supplies and drain to the bathroom. J
1600
1601
1602
ELECTRICAL:
Remove the existing wiring to the washing machine and install a dedicated circuit.
Install a single -gang cut -in box with switch and install a fixture with a globe.
AREA #4
BATHROOM:
0600
0601
0602
0800
CARPENTRY:
Frame in for a standard 30"X60" bathtub by removing the existing plaster on the two
walls and framing a third wall which will be the,plumbing wall.
0801
0802
DOORS AND WINDOWS:
Adjust and tighten the existing bathroom doors to include the door hardware.
Remove the existing bathroom window and install single hung, vinyl wrapped, "low E"
opaque window to include all stops and trim.
0900
0901
FINISHES:
Install approved underlayment, vinyl and cove base.
1100
1101
1500
APPLIANCES:
Install an approved bathroom fan and vent to the exterior with 4" metal venting, 4" R.V.
roof can, ducting insulated to R-11 and all seams sealed with duct tape and secured with
zip:screws. Install a 2 -gang box by the North door and install a 60 -minute timer.
1501
1502
PLUMBING:
Plumb in a tub/shower valve, waste drain overflow and drain lines. The plumbing will
be installed other than the exterior wall. Install a bath tub.
Plumb in supplies and drain to the bathroom vanity.
1600
1601
1602
ELECTRICAL:
Install a G.F.C.I. outlet and a three way switch in a 2 -gang box by the South door.
Install a 3 -way switch by the North door to operate a ceiling light fixture with globe.
Page 3of6
SECTION
NUMBER
DEM -KW i ivn
BATHROOM CONTINUED:
AREA #4:
1800
PAINTING:
in the area behind the vanity.
1801
Scrape and prep all loose areas in the bathroom. Patch
Install to a 8' height and
1802
Install "Marlite" over the existing bathroom walls. vertically
trim around the top of the "Marlite".
1803
Patch above the "Marlite", coat the walls, prime and splatter.
Paint the bathroom on the walls above the "Marlite" and on the ceiling.
Install a tub -kit with shelves. Do not spot glue but full spread the glue on the back.
1804
1805
KITCHEN:
Area #5:
CARPENTRY:
Remove the existing base and upper cabinets.
Install new upper and lower cabinets with a pre -formed countertop. Patch behind the
existing counter and drywall.
0600
0601
0602
0800
DOORS AND WINDOWS:
Remove the existing kitchen door and install a metal insulated door with lockset, dead -
bolt and peep -sight.
0801
0802
Remove the three kitchen windows above the kitchen sink and install one horizontal
sliding, vinyl wrapped, "low E" thermopane window.
0900
FINISHES: •
0901
Install approved underlayment, screw down, install vinyl and cove base
1500
PLUMBING:
1501
Install a new kitchen sink and faucet to include all supplies and drain.
1600
ELECTRICAL:
1601
Install two dedicated kitchen outlets to the counter area and install a dedicated circuit
to the microwave.
1602
Install a light with a globe above the kitchen sink on the soffit and install a single -pole
switch in a single gang -box on the counter area.
1603
Remove the old switch to the porch light, install a single -gang cut -in box and blank.
Install a cut -in box by the kitchen door and install a single -pole switch to operate a
porcelain fixture in a 4/0 cut -in box to be located on the same wall but on the exterior.
1604
Remove the two existing florescent fixtures and install 2- four tube, four foot fixtures;
(troffers); into the existing suspended ceiling. Install earthquake clips.
Install new ungrounded receptacles in the kitchen area to replace the existing outlets.
Page 4 of 6
SECTION
NUMBER
DESCRIPTION
-
AREA #6
LIVING/DINING ROOMS:
0800
DOORS AND WINDOWS:
0801
Replace the existing entry door with a metal insulated door with lockset, peep, and
deadbolt.
0802
Remove the two double hung windows and replace with on horizontal sliding vinyl
wrapped "low E" window. Remove the divider between the windows.
0803
Remove the old glazing on the fixed window and reglaze this window.
0804
Remove the front swing window and replace with a vinyl wrapped picture
window.
1600
ELECTRICAL:
1601
Install duplex receptacles as per Washington State Electrical Codes.
Install the ceiling fan from the bedroom in the dining room and install a new globe.
1602
Check the porch light and switch for proper operation.
1800
PAINTING:
1801
Remove all loose materials by the existing arch between the living and dining
rooms. Patch the holes and loose material. Remove the wood stove backing on
the east wall and install a chimney cap: Prime and paint the living & dining rooms.
AREA #7
BASEMENT:
0600
CARPENTRY:
0601
Remove all 1"X4"s , plywood and pegboard around the basement.
0602
Board the window opening that vents the dryer and install 4" metal venting.
0700
THERMAL AND MOISTURE PROTECTION:
0701
Install a R-19 drape using "metal building insulation" to all perimeter walls. Drape
so that the insulation is extended three feet into the basement.
0702
Install R-19 rim and end above the basement door.
0703
Install ground cover to all soil areas in the basement.
0704
Wrap the hot and cold lines 5' with rigid pipe insulation.
0800
DOORS AND WINDOWS:
0801
Remove the existing basement door and replace with a metal insulated door with
a lockset and deadbolt. Remove the existing lid to this door from the job -site.
0802
Replace the window and sill plate by the gas meter. Frame in pressure treated
lumber and install a vinyl wrapped awning window. Install a window well.
1500
PLUMBING:
1501
Install a % ball valve as a interior plumbing shut-off.
Page 5 of 6
•$-fir`
Y
AREA #7
BASEMENT CONTINUED:
1502
Remove the galvanized pipe from the ground and plumb from the main to the
washing machine, bathroom vanity, tub/shower, across the basement to the
kitchen and plumb to the water heater.
1503
Eliminate the supplies to the old basement sink.
1504
Install the drain to the kitchen sink into the existing drain line and couple with a
"Fernco" fitting.
1600
ELECTRICAL:
1601
Complete a 200 amp service change to include backing for the electrical panel.
1602
Remove the zip -cord from the west side light and install a porcelain fixture.
1603
Remove the old light fixture on the east side by the fumace and install a porcelain
fixture.
1604
On the basement Light switch handy box install romex connectors and loom to
secure the wiring.
AREA #8
EXTERIOR:
0400
MASONRY:
0401
Mortar in the opening in the foundation on the southeast corner.
0600
CARPENTRY:
0601
Remove and dispose of all existing soffit materials
0602
Box in the soffits and install continuous soffit venting on both sides.
0700
THERMAL AND MOISTURE PROTECTION:
0701
Baffle around the existing attic insulation to allow the soffit to properly vent.
0702
Enlarge the wood under the existing roof cans.
0703
Insulate the walls to include the kitchen and laundry room exterior walls.
0704
Install one-piece gutter to the east and west sides of the home to include down-
spouts. Install a ten -foot length above the back porch with a downspout.
0800
DOORS AND WINDOWS:
0801
Move the kitchen door that had been removed to the back porch.
0802
Replace the broken panes of glass on the existing windows.
0803
In the storage area behind the southwest bedroom board the open window and
replace the broken panes of glass in the window which is now boarded. Flush the
plywood to the exterior and remove the three windows.
1600
ELECTRICAL:
1601
Remove the old light fixture on the east side of the home.
Page 6of6
1800
PAINTING:
1801
Bid to fill in the missin: cedar sidin:, scra.e, .rime and saint all exterior surfaces.
MISC.
ADDITIONS TO THE ORIGINAL BID:
OPTION:
Include a cost to remove the existing roof, re -sheet and install 25 -year 3 -tab. One
side of the roof has been completed. This is a separate cost that may be included
b the homeowner. Do not include this cost in the above bid.
OPTION
Bid to install vinyl siding around the home to include wrapping the windows and
installin: vin 1 to the soffits. Bid this s- Iaratel .
NOTE:
Due to the knob and tube electrical wiring that is present we require that the
electrician include a knob and tube inspection which will be presented to the
• eneral contractor which is awarded the rehab contract.
c_rsit
SNAP
Contract Addendum
ATTACHMENT TO PROJECT NO.:
PROPERTY OWNER:
ADDRESS:
PHONE:
CONTRACTOR:
ADDRESS:
PHONE:
WORK LIST: (Description of Work)
REHABITATION
� K
CONTRACTOR SIGNATURE DATE
HOMEOWNER SIGNATURE DATE
HOMEOWNER SIGNATURE DATE